Dinoplex AEC101 cases
Moderators: doublegarage, Philt68
-
- Posts: 168
- Joined: Sat Feb 21, 2015 8:42 am
- Dino: Fiat Dino 2.0 Coupe
- Location: The Netherlands
- Contact:
Dinoplex AEC101 cases
Just finished my first 'reproduction' dinoplex AEC101 case for my own Coupé today.
This is a new casting, new casted switch body, 3D printed wire feedthrough, new designed ID-plates etc. etc.
I will be using this one for my Dino but I had a limited amount of extra cases casted. If anyone will be looking for an AEC101 case I will most likely be able to deliver them.
This one I made is prepared to mount Adrians bosch ignition module inside but I can also prepare them for points based ignition systems to mount an MSD ignition inside.
This is a new casting, new casted switch body, 3D printed wire feedthrough, new designed ID-plates etc. etc.
I will be using this one for my Dino but I had a limited amount of extra cases casted. If anyone will be looking for an AEC101 case I will most likely be able to deliver them.
This one I made is prepared to mount Adrians bosch ignition module inside but I can also prepare them for points based ignition systems to mount an MSD ignition inside.
Re: Dinoplex AEC101 cases
wow ,very impressive work.
Re: Dinoplex AEC101 cases
Hi
I would be very interested to purchase one from you. I bought an electronic set up from superformance..item;30817145
will this fit into this case? Any trick to putting it inside...
let me know by private message cost and payment method. I am in california..
Regards
H
I would be very interested to purchase one from you. I bought an electronic set up from superformance..item;30817145
will this fit into this case? Any trick to putting it inside...
let me know by private message cost and payment method. I am in california..
Regards
H
Re: Dinoplex AEC101 cases
Hello,
would be the price interesting for this group ? I think yes.....
kind regards
Peter
would be the price interesting for this group ? I think yes.....
kind regards
Peter
-
- Posts: 168
- Joined: Sat Feb 21, 2015 8:42 am
- Dino: Fiat Dino 2.0 Coupe
- Location: The Netherlands
- Contact:
Re: Dinoplex AEC101 cases
Hi Peter,
They are €795,-. That is for a complete dinoplex case with switch body, switch, gasket, new Warning/Caution lables, plastic 3d printed feed through for the wires etc. etc.
I have limited stock and it's just something i make in my free hours beside my regular job. It's quite labor intensive to finish them to a good standard so it really depends on my normal work schedule and pressure how much time i have left in a month to finish some of these casings.
If people are able and willing to finish (detail / file / sand / blast) them themselves they are cheaper, but as said be warned because it takes quite some time.
Regards Stefan
They are €795,-. That is for a complete dinoplex case with switch body, switch, gasket, new Warning/Caution lables, plastic 3d printed feed through for the wires etc. etc.
I have limited stock and it's just something i make in my free hours beside my regular job. It's quite labor intensive to finish them to a good standard so it really depends on my normal work schedule and pressure how much time i have left in a month to finish some of these casings.
If people are able and willing to finish (detail / file / sand / blast) them themselves they are cheaper, but as said be warned because it takes quite some time.
Regards Stefan
- alh
- Posts: 133
- Joined: Wed Nov 13, 2013 11:12 pm
- Dino: Ferrari Dino 246 GT
- Location: Berlin, Germany
- Contact:
Re: Dinoplex AEC101 cases
Just a heads up, 30817145 is the old Super4 ignition from Superformance, which is a copy of the seventies Bosch TSZ combined with a Bosch coil and ballast resistor. You won't gain much installing this in a Dino compared to a simple points and coil ignition except less point wear. Would recommend to rather install an MSD 6 based ignition or the high power bosch conversion Stefan mentioned to be on the same performance level of the original Dinoplex ignition.dinoverde wrote:Hi
I would be very interested to purchase one from you. I bought an electronic set up from superformance..item;30817145
- Tobi
- Site Admin
- Posts: 536
- Joined: Thu Nov 14, 2013 7:56 am
- Dino: Fiat Dino 2.4 Coupe
- Location: Upper Palatinate - Bavaria
Re: Dinoplex AEC101 cases
Good to know!alh wrote:Just a heads up, 30817145 is the old Super4 ignition from Superformance, which is a copy of the seventies Bosch TSZ combined with a Bosch coil and ballast resistor. You won't gain much installing this in a Dino compared to a simple points and coil ignition except less point wear. Would recommend to rather install an MSD 6 based ignition or the high power bosch conversion Stefan mentioned to be on the same performance level of the original Dinoplex ignition.
Thank you, Adrian!
By the way, isn't it possible to rebuild a AEC103 setup with this information (http://www.dinoplex.org/PDF/AE103_Circu ... iagram.pdf) to install the most close-to-original solution into an old or new-cast housing? The 103 has the advantage of available coils.
- alh
- Posts: 133
- Joined: Wed Nov 13, 2013 11:12 pm
- Dino: Ferrari Dino 246 GT
- Location: Berlin, Germany
- Contact:
Re: Dinoplex AEC101 cases
Yes, but assembling the required transformer is expensive and the original AEC103 circuit is quite complex. The AEC101 has about half the components
It would be more effective to install an MSD 6 series electronics or the CDI ignition made by Fred Winterburn if you want to install a CDI ignition like the original Dinoplex.
It would be more effective to install an MSD 6 series electronics or the CDI ignition made by Fred Winterburn if you want to install a CDI ignition like the original Dinoplex.
-
- Posts: 168
- Joined: Sat Feb 21, 2015 8:42 am
- Dino: Fiat Dino 2.0 Coupe
- Location: The Netherlands
- Contact:
Re: Dinoplex AEC101 cases
I'm working on a solution to make it as easy as possible to convert the dinoplexes with MSD (programmable) internals. This option will have all the benefits of new electronics like accepting both points setup as electronic triggers while at the same time keeping the stock CD type of ignition.
Working on it for both the AEC101 and 103. If I worked something out that will make it easy plug and play I'll get back on it.
Working on it for both the AEC101 and 103. If I worked something out that will make it easy plug and play I'll get back on it.