Search found 117 matches
- Wed Jun 21, 2023 9:27 pm
- Forum: Technical Discussions
- Topic: Gemmer steering box
- Replies: 22
- Views: 22969
Re: Gemmer steering box
I was under the impression that some of the parts could be sourced from Lada steering boxes, or that the latter could be made to fit. Does anyone else know about this?
- Wed May 17, 2023 9:47 pm
- Forum: Technical Discussions
- Topic: Chain tensioner leaking
- Replies: 7
- Views: 2904
Re: Chain tensioner leaking
If I remember right, you assemble the tensioner on your bench and compress the spring before tightening it. Then, you bolt the pre-loaded tensioner on the head and release tension once it's on. Good tip on the counter-bolt, it was a Ferrari "upgrade" for the 246 at the time. Concerning the...
- Wed Feb 15, 2023 10:18 pm
- Forum: Technical Discussions
- Topic: Compression Test Results
- Replies: 18
- Views: 4827
Re: Compression Test Results
I don't think he has bought the car...yet. If it was mine, I would continue driving it until something showed up indicating real engine work was needed. If it was going to be mine, I would factor in some money for the engine. These are great cars and the engine is very solid if properly looked after...
- Wed Feb 15, 2023 12:52 pm
- Forum: Technical Discussions
- Topic: Compression Test Results
- Replies: 18
- Views: 4827
Re: Compression Test Results
Interesting numbers, how are you interpreting them? The lower losses on # 3 and #6 could be due to them being first in line to receive oil from the pump to the heads, although I don't see why this should affect the leak-down unless enough oil was getting into the cylinder to reduce leakage (leaky va...
- Tue Jan 24, 2023 10:56 pm
- Forum: Technical Discussions
- Topic: Compression Test Results
- Replies: 18
- Views: 4827
Re: Compression Test Results
I would not worry too much about the actual values if they are the same and the milage is low. The values depend on the dead volume of the rubber hose and fitting wrt that of the cylinder volume and compression. You can correct for this if you know both. Evenly low compression on all cylinders could...
- Sat Nov 12, 2022 2:38 pm
- Forum: Technical Discussions
- Topic: Candle in the wind...
- Replies: 12
- Views: 2772
Re: Candle in the wind...
Mine improved considerably after fitting relays under the dash. The are operated by the poor, oxidised contacts in the steering stalk and power the lights with a fresh +12V sourced from the connector. I also wired them so that the high beams would not turn off the driving lights, giving really good ...
- Fri Sep 16, 2022 10:30 pm
- Forum: Technical Discussions
- Topic: 2400 Coupe engine rebuild
- Replies: 42
- Views: 15211
Re: 2400 Coupe engine rebuild
Hi, you are correct about the plugs being threaded on the ferrari crankshafts. I would assume that they are as well on these but, as you can see, they were inserted and ground flat against the counterweights. So, not much left to get a hex key in there to undo them. The place I bought mine to simply...
- Fri Sep 16, 2022 10:22 am
- Forum: Technical Discussions
- Topic: 2400 Coupe engine rebuild
- Replies: 42
- Views: 15211
Re: 2400 Coupe engine rebuild
Hi, the crankshaft should be brought to the machine shop (along with the heads): They will drill out the plugs, clean the inside passages, and put in new plugs. There is a lot of crud that deposits in the recessed areas of the oil galleys. If it comes lose during the rebuild, it can end up on the be...
- Thu Sep 08, 2022 12:06 pm
- Forum: Technical Discussions
- Topic: removing brake master cylinder
- Replies: 7
- Views: 1685
Re: removing brake master cylinder
Ditto, brake MC rebuild kit from superformance and removed/installed it on my back w/o the driver's seat and steering column. I did not drop the pedal box and it was a PITA for sure. Doable, no leaks since 10 y... The MC is solid, with little to go wrong except the perished rubber. If yours comes ou...
- Mon Jun 27, 2022 1:30 pm
- Forum: Technical Discussions
- Topic: Coupe Fuel Tank
- Replies: 8
- Views: 2377
Re: Coupe Fuel Tank
Hi, I would try to contact Maurizio Zanella, he has a lot of spares for these cars. It will, however, add shipment from Italy.
Good luck,
Dario
Good luck,
Dario